Normally-open, direct-acting solenoid valves for aggressive chemicals

POM Home Page This page has links to specific products, and is sort of a site map Catalog Pages in .PDF format Articles & FAQs about all types of Plastic Valves & Applications Who's who at Plast-O-Matic, Map to find our plant and offices in Cedar Grove, Trade Show schedule, Customer Reference list & much more... Clickable map of Distributors, also some helpful Industry Links Quote Request Form, also for special or custom valves

Normally-Open Solenoid Valves

True Blue® Solenoid Valves Series EASY-N.O. with quad seal design for pressure, drain, and vacuum service.

Series EASY-NO is a normally-open solenoid valve for all types of nasty chemicals, as well as ultra-pure liquids.

Series EASY-NO (NORMALLY OPEN):

For applications requiring a valve to remain open when de-energized, or when it would be dangerous for a valve to close during a power failure. (e.g. cooling towers, emergency systems, etc.)

Million-cycle, bubble-tight shutoff, with no metal parts in wetted area. Design features a non-sticking PTFE shaft with a 4 u-cup seal, plus upper seal with Fail Dry safety vent. Suitable for most solutions, although proper caution should be taken when specifying for liquids prone to crystallization because of the u-cup design.

The EASY-N.O. may also be appropriate if you require a valve to remain open for a long period of time (open much more than closed). This will result in less wear, and can result in substantial energy savings.

Mode of Operation:

Normally OPEN (energize to close). No pressure differential required.

Service:

Pressure, drain, and vacuum. (must specify with order). May not be suitable for applications prone to crystallization.

     Note: Handling of Dry Chlorine & Use of Thermoplastic Valves: When ordering a valve for chlorine service, please specify "Chlorine-Vacuum" on the order.  Plast-O-Matic Valves are not recommended for use with pressurized dry chlorine gas.

Application:

Series EASY-N.O. allows continuous flow of highly corrosive and ultra-pure liquids. They can handle acids, solvents, process water, deionized water, etc. and do not require pressure to aid in opening the valve.

Design:

Valves are spring return normally open and direct acting with a heavy duty push-pull plunger design. There is no minimum pressure required for operation. Multiple U-cups are mounted around a PTFE shaft for low friction sealing, non-sticking operation, and million cycle design. The quad U-cup design also allows a stock valve to be used for vacuum or pressure. A poppet seat ensures bubble-tight shutoff. External fasteners are stainless steel (no metals in wetted area).

Available in 1/4" and 1/2", the EASY-N.O. has a Cv rating of 1.1, which provides excellent capacity within these pipe sizes.

After 1,000,000 cycles, we recommend that the valve be disassembled and inspected. It is also recommended to replace the elastomer seals and u-cups at this point. Contact your distributor for a seal kit. For heavy use applications, you may wish to order a spare seal kit with the valve. Seal replacement takes but a few minutes with common tools; no special training is required.

Pressure considerations:

Inlet pressure to 70 psi (4,8 bar) at room temperature (75 F). Backpressure rated to 18 psi (1,2 bar). Excessive backpressure will cause this model to remain open when the coil is energized.

Coil Info:

A 20 watt continuous duty coil is standard. When the coil is energized, the valve closes and will remain closed until the coil is de-energized. Coils are available in general purpose or explosion-proof, water tight construction. AC voltages are 24, 120, 240 and 480. DC available; please call our Tech Group at 973-256-3000. Other coils available.

Dimensions & Specifications:

dimensions of the True Blue EASY-N.O. solenoid valve.

specifications and model numbers for the classic True Blue normally-open solenoid valve

**Model numbers shown with "W20" NEMA 4X coils. If explosion-proof coil is required, replace "W20" with "E20" in the part number.

NOTES: Maximum inlet pressure ratings are at full line voltages of 24, 120, 240, etc. For a 10% voltage reduction these inlet pressure ratings will be approximately 30% lower.

Other materials are available; consult factory - (973) 256-3000

Helpful Links:

Installation Instructions, maintenance and parts drawings in .pdf format

Determining Amperage for a Plast-O-Matic Solenoid Valve This is a technical document in Microsoft Word format that explains how to calculate the amperage required for Plast-O-Matic AC or DC coils.

Overview of the Entire Solenoid Valve Line, which may be the page you were on prior to this one. Provides key items for quick comparison and selection.

Series EASM & EASYM, 2-way molded solenoid valves that use a triple u-cup seal. These diaphragm valves are well suited to vacuum, pressure and drain applications. But for salt solutions, caustics, etc., use either of the next two valves. Range of sizes is 1/2", 3/4" & 1".

Series EASMD & EASYMD, 2-way molded solenoid valves that use a rolling diaphragm. These diaphragm valves are well suited to salt solutions, caustics, and other crystallizing liquids, but they are not designed for vacuum applications. Range of sizes is 1/2", 3/4" & 1".

Series EASMT & EASYMT 2-way Molded solenoid valves that use a dynamic PTFE bellows seal in lieu of u-cups or rolling diaphragms. The PTFE bellows line replaces all the different seal configurations, is suitable for all types of solutions, and all types of service. Range of sizes is 1/2", 3/4" & 1".

Series EAST, Compact valve with outstanding performance. Uses PTFE bellows dynamic seal, 1/4" & 1/2" sizes.

Series PS, Pilot-operated valve with outstanding pressure and flow performance. Uses PTFE bellows dynamic seal. Complete sizes 1/2" through 3", requires 5 psi differential for proper operation.

Series THP, Compact 3-way (aka diverter) solenoid valve.

Series WCM, Compact, direct-acting 2-way valve with stainless steel & silver wetted core. (this is the only Plast-O-Matic solenoid valve with a wetted metal core). Offers an outstanding combination of price and performance.

Pressure Drop Calculator How will a particular solenoid valve affect the pressure in your piping system? If you know your approximate flow rate in gallons per minute, this calculator will tell you your pressure drop, or "Delta P."

Additional Info: Catalog Request Catalog EASY-NO

Plast-O-Matic Valves, Inc.
1384 Pompton Avenue
Cedar Grove, NJ 07009 USA
Voice: (973) 256-3000
Fax: (973) 256-4745

email

Top of Page

Kynar® is a registered trademark of Arkema.,
Corzan™ is a trademark of Noveon, Geon® is a registered trademark of the Geon Company.
Viton® is a registered trademark of DuPont Dow Elastomers.

FAIL-DRY® and TRUE BLUE® are registered trademarks of Plast-O-Matic Valves, Inc.

Copyright © 1997-2005 Plast-O-Matic Valves, Inc.

DID YOU KNOW that Plast-O-Matic was originally named "Valvematic Controls"? Founder Bruce L. DeLorenzo used the name in 1966 on his preliminary designs, but later found out that it had been trademarked decades earlier. When he and Daniel McCarthy "officially" started operations in 1967, the Plast-O-Matic name was introduced. The first valves were air shutoffs designed for a highly corrosive process in the dry cleaning industry. In those early days the company was headquartered in the DeLorenzo family garage! After moving to larger quarters in Clifton, then a larger shop in Totowa, NJ, the company settled at the current headquarters and factory in Cedar Grove, NJ in 1995. Many things have changed at Plast-O-Matic since 1967, but our commitment to solving problems for tough applications remains unchanged.
counter
Hit Counter
Web Counter